E-Bike Kit Parts

Tongsheng TSDZ2B thumb throttle. E-Bike 36-48V Thumb Throttle Speed Control  For TSDZ2B Applicable  to the left and right sides of the installation position Simple and easy to install Made of high quality material, durable and practical to use

Tongsheng Crank Arms Square Tapered Left & Right Crank Arms 170MM in Length - Measured from centre of pedal thread hole to centre of square taper hole. For use with Tongsheng Mid Drive Conversion Kits

Tongsheng Display for use with Tongsheng TSDZ2B Mid-Drive motor. Full colour display 6 Pin connection (second image shows remote controller - available seperately) 3.5”TFT, Fully screen (No borders） Full Specification Size L*W*H                   63.*93*22mmHolder                            φ22.2/25.4/31.8mmRemote                          φ22.2/23.8mmCommunication            UART/ CANCore DataScreen                            3.5”Display Type                  TFTVoltage                           24V/36V/48VFunctionBAT, Headlight, Walk, PAS level, Speed, Trip, ODO, TripTime, Mile/KM. Error CodeConnector Type: 6-pin waterproof plugwater proof Cable...

CYC Chainring for use with CYC Photon Motors. Includes: Starfish adaptor Chainring Aluminum chainring cover on 38, 42 and 50 teeth sizes Carbon Fibre chainring cover on 34 teeth version

CYC Crank Arms for use with CYC Motors. These ISIS crank arms have a 5 degrees off-set & made to be paired with the Gen 3 & Photon kits. Material = 7075-t6 Aluminium Compatibility = X1 Pro Gen 3, X1 Stealth Gen 3, & Photon 165mm...

  Kit includes; left cup, Isis axle, spacers, tool, axle bolts, grease, zip-ties (Ruler not included) Spindle Length Options: 180mm suitable for 68/73/83mm bottom bracket options 200mm suitable for 100mm & BB92 bottom bracket options 220mm suitable for 120mm bottom bracket options

Compatible with X1 Pro Gen 2 & X1 Stealth Gen 1 kits Includes: throttle and matching grip

Extension Cable & Mounting bracket / cover plate for X series controllers. Designed to allow controller to be mounted further away from motor, normally up behind the seatpost. Complete with mounting bolts.

Includes 1x universal thumb throttle. Specifications: Left or right side handlebar mounting Compatibility = X1 Pro Gen 3, X1 Stealth Gen 3, & Photon

Pair of adapter cups to allow BB92 to fit a BSA bottom bracket, comes with spacers. Compatible with Photon & Gen 3 Motors.

SW102 display with CYC specific firmware integrated with the controller and the CYC Ride Control mobile app. It's convenient size leaves you with plenty of space on your handlebars. Plug-n-play ready. Includes: SW102 display Specifications: Nominal Voltage = 36-52V  Waterproof = IP65 Controller Compatibility =...

DS103 display has CYC specific firmware integrated with the controller and the CYC Ride Control mobile app. It's easy-to-read formfactor gives you all the stats you'll need on the go. Plug-n-play ready.  Includes: DS103 display Specifications: Nominal Voltage = 36-52V  Waterproof = IP65 Controller Compatibility =...

Universal thumb throttle (3-wires). Compatible with our HUB drive conversion kits.

Multi-magnet pedelec with clip-on sensor.

Easy to install one-piece pedelec sensor. Simply remove the crank arm and push it on! No need to fiddle with retaining rings!

This design was engineered to make use of the existing fender eyelet holes that are on most front forks. This can lead to a smaller arm and a tidier installation than using hose clamps around the fork, and we recommend its use whenever there...

LCD4 Display Suits motor type: Hub Size: Extra small Colour: Black and white Connector type: Green Juliette Cable length from display to buttons: integrated display and buttons Best for use when space on handlebars is limited. Adapter cable available.

LCD7 Display Suits motor type: Hub Size: Small Colour: Colour Connector type: Green Juliette Cable length from display to buttons: integrated display and buttons Best for use when a discreet and small display is required, for example on cruiser bars or when a front...

LCD8 Display – Hub Motor Suits motor type: Hub Size: Large Colour: Colour Connector type: Green Juliette Cable length from display to buttons: 24cm Best for use when a large and easy to read display is required. Adapter cable available.

Front Hub Motor Install Tool Kit includes; Tyre levers, crank extractor and spoke spanner.

Standard Pedelec Fit Kit includes; Lockring tool, Crank remover and lockring. (No Pedelec Sensor Included in this kit)

Engage the motor without pedalling, great for a standing start, or over-ride when in lower assist levels. This is the lever model, which looks and operates much like a gear shifting lever. It sits anywhere on the narrow parts of the handlebar, including curved...

Engage the motor without pedalling, great for a standing start, or over-ride when in lower assist levels. Button engages CRUISE CONTROL on our systems, brake cutout will disengage. This half-twist model is designed to be mounted on the right hand side of the handlebar,...

The Bafang BBS locknut tool is a very specific tool required for the removal and refitting of the axle assembly on the Bafang BBS motors. (Photo's show the axle assembly, this is for illustration purposes only to show how the tool fits the axle....

Oil Seal for the Bafang BBS motors main axle,